manualshive.com logo in svg

Daikin RXL25G2V1B, Руководство по обслуживанию

Поделиться
Скачать
Daikin RXL25G2V1B Скачать руководство пользователя страница 62

Control Specification

SiENBE04-925_A

48

Function and Control

3.13 Forced Operation Mode

Outline

Forced operation mode includes only forced cooling.

Detail

3.14 Standby Electricity Saving

20/25 Class Only

This function turns power supply OFF to the outdoor unit and sets the indoor unit into energy-
saving mode, thus reducing the power consumption of the air conditioner.

For 20 class models, field setting is required for turning ON the function.

Refer to “Standby Electricity Saving” on page 269 for detail.

Item

Forced Cooling

Conditions

1) The outdoor unit is not abnormal and 
not in the 3-minute standby mode. 

2) The outdoor unit is not operating. 

The forced operation is allowed when 
the above both conditions are met.

Start

1) Press the forced operation ON/OFF 
button (SW1) on the indoor unit for 5 
seconds.

2) Press the forced operation ON/OFF 
button (SW1) on the outdoor unit.

Command 
frequency

RXL20G2V1B: 68 Hz
RXL20G2V1B9: 58 Hz
RXL25G2V1B: 47 Hz
RXL35G2V1B: 66 Hz

End

1) The operation ends automatically 
after 15 minutes.

2) Press the forced operation ON/OFF 
button (SW1) on the indoor unit again.

3) Press the ON/OFF button on the 
remote control.

4) Press the forced operation ON/OFF 
button (SW1) on the outdoor unit.

Others

The protection functions are prior to all 
others in the forced operation.

SIENBE04-925_A_FRONT.pdf   62

24/02/2011   13:53:53

Содержание RXL25G2V1B







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды