manualshive.com logo in svg

Daikin RXL25G2V1B, Руководство по обслуживанию

Поделиться
Скачать
Daikin RXL25G2V1B Скачать руководство пользователя страница 175

Outdoor Unit - RXL20G2V1B

SiENBE04-925_A

160

Removal Procedure

4

Disconnect the 
connector for the fan 
motor [S70].

5

Release the fan motor 
lead wire from the hook.

6

Open the hooks and 
release the fan motor 
lead wire.

„

When reassembling, put the 
fan motor lead wire through 
the back of the fan motor (so 
as not to be entangled with 
the outdoor fan).

7

Remove the 4 screws 
and remove the fan 
motor.

„

Be sure to remove the lower 
screws first. If the upper 
screws are removed first, the 
fan motor, the center of 
gravity of which is toward the 
front, may tilt down or fall, 
getting you injured.

Step

Procedure

Points

(R9332)

[S70]

Fan motor 
lead wire

(R7200)

(R7201)

(R3249)

Lead wire

Outdoor fan

Fan motor

(R7202)

SIENBE04-925_A_FRONT.pdf   175

24/02/2011   13:54:04

Содержание RXL25G2V1B







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды