Daikin RXL25G2V1B Скачать руководство пользователя страница 192

Страница: 192 / 294

SiENBE04-925_A

Outdoor Unit - RXL20G2V1B

Removal Procedure

177

2.7

Removal of Sound Blanket

Procedure

Warning

Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.

Step

Procedure

Points

Untie the string and
open the sound blanket
(outer).

Preparation

Remove the outer panels
according to the “Removal of
Outer Panels / Fan Motor”.

Remove the electrical box
according to the "Removal of
Electrical Box".

Lift and remove the
sound blanket (outer).

Since the piping ports are
torn easily, remove the
sound blanket carefully.

Remove the sound
blanket (top).

Pull the sound blanket
(inner) out.

(R7229)

Sound blanket (outer)

(R12212)

(R7231)

Sound blanket
(top)

Sound blanket (inner)

(R12271)

SIENBE04-925_A_FRONT.pdf 192

24/02/2011 13:54:07

Содержание RXL25G2V1B







































































































































































































































































































Результаты поиска

Содержание RXL25G2V1B

Отзывы:

Бренды по названию

Популярные бренды

Daikin RXL25G2V1B, Руководство по обслуживанию

Результаты поиска

Содержание RXL25G2V1B

Отзывы:

Бренды по названию

Популярные бренды