Crestron D3 PRO Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 104

background image

Software

Crestron

D3 Pro

™

•

You can adjust lighting levels in real time.

Actions and Events

The programming view allows you term

programming

defines the act of assigning

one or more

actions

to one or more

events

. An event occurs when a device’s output

exhibits a certain behavior, such as, goes from low to high. Most events in a D3 Pro
lighting system occur when a button on a keypad or touchpanel is pressed, released,
or held for a certain time.

Thus, in the most basic sense, an event could be a button press and the action could
be to set the lights to a specified level.

The Programming View allows you to assign actions to any device in your system
that is capable of generating events. The most common example of such an event are
button events that come from user-interfaces. However, other devices may generate
events, such as the Scheduler, or other devices added to the system such as photocells
and motion detectors.

Digital, Analog, and Serial Commands

All devices in D3 Pro can be controlled through a combination of digital, analog, or
serial commands. The commands are identified by icons, as shown in the following
table:

Command Type

Icon

Unaffected

Edge-triggered digital command

Level-triggered (maintained) digital
command

Analog command

Serial command

D

IGITAL

C

OMMANDS

A digital command is a simple instruction sent to a device, such as the Open
command issued to a motor, or the Raise command issued to a dimmable light. In
reality, digital commands are not so much issued to a device as they are activated and
deactivated. This means that a digital command can be maintained simply by
activating it and then waiting some period of time before deactivating it.

In practice, some digital commands will affect the device for as long as they are
maintained, and others will affect the device only when they are first activated (also
called the rising edge). For the latter, maintaining the digital command will not cause
any harm, but it is not necessary.

By default, D3 Pro will maintain all digital commands for as long as the event they
are in is active. The question then becomes "How long are events active?" This can
be determined using a simple rule: All "Press" events (e.g. Press, Press 2, Press 3,
etc.) plus the "Hold" event on Press and Hold buttons will be active for as long as the

46

•

Crestron D3 Pro™

Reference Guide – DOC. 5998a

«
...
48
49
50
51
52
...
»

Содержание D3 PRO









































































































Отзывы:

Нет отзывов

Похожие инструкции для D3 PRO

MOBILE SECURITY FOR WINDOWS MOBILE -

Бренд: F-SECURE Страницы: 4

MOBILE SECURITY FOR UIQ -

Бренд: F-SECURE Страницы: 3

MOBILE SECURITY 6 FOR WINDOWS MOBILE -

Бренд: F-SECURE Страницы: 5

MOBILE SECURITY 6 FOR S60 -

Бренд: F-SECURE Страницы: 5

CLIENT SECURITY 7.00

Бренд: F-SECURE Страницы: 315

ANTI-VIRUS FOR MICROSOFT EXCHANGE 9.00

Бренд: F-SECURE Страницы: 115

ANTI-VIRUS FOR MICROSOFT EXCHANGE 8.00 -

Бренд: F-SECURE Страницы: 349

ANTI-VIRUS - FOR MICROSOFT EXCHANGE

Бренд: F-SECURE Страницы: 224

Бренд: FARONICS Страницы: 5

Бренд: FARONICS Страницы: 2

DEEP FREEZE ENTERPRISE

Бренд: FARONICS Страницы: 3

ANTI-EXECUTABLE ENTERPRISE

Бренд: FARONICS Страницы: 2

Hosted Provider Edition (HPE) 8.1

Бренд: Genesys Страницы: 5

Бренд: Brocade Communications Systems Страницы: 60

Бренд: Teklynx Страницы: 30

Бренд: Arturia Страницы: 10

WISE INSTALLATION EXPRESS 7.0 SP2

Бренд: Symantec Страницы: 50

Бренд: Paradyne Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды