Cosmed Q-NRG Скачать руководство пользователя страница 113

Страница: 113 / 152

REF C04717-02-91 Q-NRG User Manual, Edition 4.2

Chapter 6 - Troubleshooting

COSMED srl

Error#104
Cylinder gas not detected

No calibration gas flowing into the
analyzers when expected

Review calibration set-up:
Cylinder connected
Cylinder valve Open
Output pressure 5-6bar (70-90psi)
Pressure regulator ON/OFF valve Open
Cylinder composition properly specified
in Calibration/Cal factors/References

Error#105
Environmental CO2 too high

Room air CO2 content higher than
maximum admissible (0.25%)

Make sure room is properly aerated
before performing calibration and test

Error#106
O2 sensor exhausted (Maintenance

required)

O2 output signal is lower than
minimum acceptable threshold due to
sensor aging

Replace the O2 sensor according to
maintenance instructions

Error#107
CO2 sensor not ready.
Unable to complete calibration.

CO2 sensor has not reached operative
temperature

Wait for a few minutes and try again

Failure#108
Calibration flow not detected.
Unable to complete calibration.

Internal Turbine Flowmeter does not
detect any flow although the internal
blower is properly functioning

Contact Service specifying error
message #

Error#109
Calibration flow too low

During pneumotach calibration,
internal turbine flow is too low

Calibrate internal flowmeter according
to instructions (Internal Turbine
Flowmeter - Blower Calibration) and
try again

Error#110
Calibration flow too high

During pneumotach calibration,
internal turbine flow is too high

Calibrate internal flowmeter according
to instructions (Internal Turbine
Flowmeter - Blower Calibration) and
try again

Error#111
Reversed flow detected. Swap

Flowmeter connections

Detected flow during Pneumotach
calibration is negative

Reverse Pneumotach connection
matching colour coding

Error#112
PNT flow not detected, check the

connections

Measured flow during Pneumotach
calibration is zero, regardless of proper
functioning of internal blower and
Turbine Flowmeter

Be sure the Pneumotach is correctly
connected to the device

Failure#115
Blower flow not detected

Internal Blower not functioning

Contact Service

Failure#116
Calibration Fail

Generic fail related to the calibration
procedure

Repeat the calibration; if the problem is
not solved, contact service

Failure#306
Blower Ventilation not detected,

remove the Canopy hood from

patient.

During Canopy test dilution flow is
not detected due to blower or internal
flowmeter failure

Remove Canopy hood as soon as possi-
ble and contact technical service

Содержание Q-NRG

























































































































































Результаты поиска

Содержание Q-NRG

Отзывы:

Cosmed Q-NRG, Руководство пользователя, Страница: 113 / 152

Результаты поиска

Содержание Q-NRG

Отзывы: