Canon ImageRunner 600 Скачать руководство пользователя страница 667

Страница: 667 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

13-92-2

CHAPTER 13 TROUBLESHOOTING

E069

Step

Action

Mount the transfer /
separation assembly
properly.

Correct the connection.

Correct the wiring.

Replace the transfer/
separation charging
assembly.

End.

Checks

Is the transfer/separation charging
assembly mounted properly?

Are the following connectors and screws
of the HV-DC PCB normal?
•J701
•J723
•J730

Is the connection of and the wiring from
the HV-DC PCB to the transfer/separation
charging assembly (transfer charging
assembly side) normal?

Replace the HV-DC PCB. Is the problem
corrected?

Yes/No

YES

Cause

Mounting

Connection

Wiring

HV-DC PCB

transfer/
separation
charging
assembly

J723

J730

T701

Table 13-405

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 667 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: