Canon ImageRunner 600 Скачать руководство пользователя страница 429

Страница: 429 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

9-53

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

[2]

[1]

[3]

Removing the Multifeeder Pickup
Drive Assembly

Construction

1) Remove the rear cover.
2) Remove the high-voltage transformer

(DC).

3) Loosen the mounting screw on the rear

fixing plate of the registration roller as-
sembly.

4) Remove the four screws [1], and discon-

nect the four connectors [2]; then, detach
the multifeeder pickup drive assembly
[3].

Figure 9-D708

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 429 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: