Canon ImageRunner 600 Скачать руководство пользователя страница 474

Страница: 474 / 875

10-26

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 10 SIDE PAPER DECK

Figure 10-B301

Deck Body

Detaching the Deck from the
Copier

1) Place a stack of copy paper [3] (about 8

cm in height) on the floor for placement of
the deck [2] to prevent deformation of the
roll support plate [1].

2) Remove the right cover. (See p. 10-24.)

8 cm (approx.)

[2]

[3]

[1]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 474 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: