Canon ImageRunner 600 Скачать руководство пользователя страница 108

Страница: 108 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A

3-35

CHAPTER 3 ORIGINAL EXPOSURE SYSTEM

Figure 3-D511

Figure 3-D512

[1]

[2]

[3]

[2]

Removing the Standard White
Plate

1) Remove the right glass retaining cover.
2) Remove the copyboard glass.
3) Remove the small cover [1] for the stan-

dard white plate with a flat-blade screw-
driver.

4) Remove the two screws [2], and detach

the standard white cover [3].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 108 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: