Canon ImageRunner 600 Скачать руководство пользователя страница 132

Страница: 132 / 875

4-22

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 4 IMAGE PROCESSING SYSTEM

Figure 4-A401

[1]

[2]

[3]

Figure 4-A402

[4]

Claw

CCD PCB

Removing the CCD PCB

1) Remove the copyboard glass.
2) Move the No. 1 mirror mount to the left

end.

3) Remove the one screw [1], and disconnect

the connector [2]; then, detach the original
sensor unit (rear) [3].

4) Release the front and rear claws, and de-

tach the CCD cover [4].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 132 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: