Canon ImageRunner 600 Скачать руководство пользователя страница 312

Страница: 312 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-73

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

Figure 7-D807

Figure 7-D808

2) Remove the screw [5], and detach the

front fixing plate [6]; then, detach the pre-
registration roller assembly [7].

3) Remove the two springs [8], E-ring [9],

and arm support shaft [10] at the front.

4) Remove the E-ring [11], spacer [12], and

bearing [13].

5) Perform steps 3) and 4) for the rear; then,

detach the pre-registration roller assem-
bly.

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 312 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: