Canon ImageRunner 600 Скачать руководство пользователя страница 417

Страница: 417 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

9-41

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-C716

[4]

[6]

[5]

Figure 9-C717

4) Disconnect the connector [4], and remove

the three screws [5]; then, detach the drum
fan [6].

Caution:

When mounting the drum fan, be sure
that the direction of air current matches
the marking indicated on the fan.

Removing the Inverter Cooling
Fan

1) Remove the rear cover.
2) Remove the two screws [1], and slide out

the inverter fan [2].

Caution:

When mounting the inverter cooling fan,
be sure that the direction of air current
matches the marking indicated on the
fan.

[1]

[2]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 417 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: