Canon ImageRunner 600 Скачать руководство пользователя страница 326

Страница: 326 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-87

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[1]

[3]

[2]

[1]

Figure 7-F823

Figure 7-F824

13. Removing the Front Deck (lifter)

Draw-Out Sensor

1) Disconnect the connector [1] from the

bottom of the duplexing unit; then, re-
move the screw [2], and detach the front
deck (left) feed sensor [3].

14. Removing the Horizontal

Registration Sensor

1) Remove the duplexing unit from the

copier.

2) Remove the front cover.
3) Disconnect the connector [1], and remove

the three screws [2].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 326 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: