Canon ImageRunner 600 Скачать руководство пользователя страница 295

Страница: 295 / 875

CHAPTER 7 PICK-UP/FEEDING SYSTEM

7-56

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

[1]

[2]

[3]

Figure 7-B802

Figure 7-B803

Removing the Pickup Assembly
of the Front Deck (left)

1) Slide out the deck (right, left).
2) Remove the two stoppers [2] from both

left and right of the deck (left) [1].

3) Disconnect the connector [3] from inside

the copier.

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 295 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: