Canon ImageRunner 600 Скачать руководство пользователя страница 309

Страница: 309 / 875

CHAPTER 7 PICK-UP/FEEDING SYSTEM

7-70

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

[1]

[2]

[3]

[1]

[2]

[3]

Figure 7-D801

Figure 7-D802

Registration Feeding
Assembly

Removing the Registration
Clutch/Registration Brake Clutch

1) Slide out the fixing feeding unit from the

copier.

2) Disconnect the connector [1], and remove

the grip ring [2]; then, detach the registra-
tion clutch [3].

Removing the Registration Brake
Clutch

1) Remove the transfer separation charging

assembly front cover.

2) Disconnect the connector [1], and remove

the grip ring [2]; then, detach the registra-
tion brake clutch [3].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 309 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: