Canon ImageRunner 600 Скачать руководство пользователя страница 424

Страница: 424 / 875

9-48

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-D701

Drive Assembly

Removing the Left Pickup Drive
Assembly

Construction

1) Remove the rear cover.
2) Open the system box assembly. (See Fig-

ure 4-D401.)

3) Remove the high-voltage transformer

(AC). (See Figure 9-H701.)

4) While detaching the belt [1], remove the

three screws [2], and detach the left
pickup drive assembly [3].

[1]

[3]

[2]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 424 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: