Canon ImageRunner 600 Скачать руководство пользователя страница 288

Страница: 288 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-49

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[1]

[2]

[3]

[4]

[7]

[5]

[6]

Figure 7-A813

Figure 7-A814

Figure 7-A815

Removing the Manual Feed Tray
Paper Sensor

1) Remove the mounting screw [1], and de-

tach the solenoid cover [2].

2) Remove the mounting screw [3], and de-

tach the solenoid [4] together with the up-
per plate.

3) Remove the screw [5], and detach the con-

nector cover [6]; then, disconnect the con-
nector [7].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 288 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: