Canon ImageRunner 600 Скачать руководство пользователя страница 284

Страница: 284 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-45

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[6]

[7]

[8]

[4]

[5]

[3]

Figure 7-A803

Figure 7-A801

Figure 7-A802

Manual Tray Assembly

Removing the Manual Tray Unit

1) Remove the two screws [1], and detach

the delivery tray unit [2].

2) Remove the four screws [3], and detach

the upper right cover [5] while the toner
cartridge cover [4] is open.

3) Remove the screw [6], and disconnect the

connector [7]; then, detach the manual
feed tray unit [8].

[1]

[2]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 284 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: