Canon ImageRunner 600 Скачать руководство пользователя страница 416

Страница: 416 / 875

9-40

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-C714

[4]

[3]

Figure 9-C715

7) Remove the three screws [3], and detach

the feeding fan [4].

Caution:

When mounting the feeding fan, be sure
that the direction of air current matches
the marking indicated on the fan.

Removing the Drum Fan

1) Remove the rear cover.
2) Remove the high-voltage transformer

(DC).

3) Remove the two screws [1], and discon-

nect the connector [2]; then, detach the
drum fan unit [3].

[3]

[1]

[2]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 416 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: