Canon ImageRunner 600 Скачать руководство пользователя страница 413

Страница: 413 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

9-37

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-C707

[4]

[5]

[3]

[1]

[2]

[1]

[3]

Figure 9-C708

5) Disconnect the connector [3], and remove

the two screws [4]; then, detach the stream
reading fan [5].

Removing the Laser Cooling Fan

1) Remove the copyboard glass.
2) Remove the original sensor unit 1.
3) Remove the image processor cover, and

detach the image processor PCB.

4) Remove the two screws [1], and discon-

nect the connector [2]; then, detach the la-
ser cooling fan [3] together with its
mount.

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 413 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: