Canon ImageRunner 600 Скачать руководство пользователя страница 212

Страница: 212 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

6-53

CHAPTER 6 IMAGE FORMATION SYSTEM

Figure 6-A705

Figure 6-A706

Replacing the Photosensitive
Drum Heater

1) Remove the photosensitive drum from the

copier.

2) Remove the two mounting screws [1], and

detach the flange [2] at the front; then, dis-
connect the connector [3].

3) Pull out the flange at the rear [4], and de-

tach the power supply unit [5] from the
photosensitive drum.

[1]

[2]

[3]

[4]

[5]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 212 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: