Canon ImageRunner 600 Скачать руководство пользователя страница 318

Страница: 318 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-79

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[4]

[5]

[2]

[1]

[3]

[1]

[2]

Figure 7-F805

3) Remove the four screws [4], and detach

the reversal motor [5].

Removing the Lower Feeder
Motor

1) Remove the front cover of the duplexing

unit.

2) Disconnect the connector [1], and remove

the two screws [2]; then, detach the lower
feeder motor [3].

Removing the Horizontal
Registration Motor

1) Remove the duplexing unit from the

copier.

2) Remove the two screws [1], and detach

the upper cover [2].

Figure 7-F806

Figure 7-F807

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 318 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: