Canon ImageRunner 600 Скачать руководство пользователя страница 317

Страница: 317 / 875

CHAPTER 7 PICK-UP/FEEDING SYSTEM

7-78

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

[1]

[2]

[3]

[2]

[1]

Figure 7-F803

Figure 7-F804

Removing the Reversing Flapper
Solenoid

1) Remove the duplexing unit from the

copier.

2) Remove the two screws [1], and discon-

nect the connector [2]; then, detach the re-
versing flapper solenoid [3].

Removing the Reversal Motor

1) Remove the front cover of the duplexing

unit.

2) Disconnect the two connectors [1] , and

remove the four screws [2]; then, detach
the reversal motor together with the motor
support plate [3].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 317 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: