Canon ImageRunner 600 Скачать руководство пользователя страница 358

Страница: 358 / 875

8-30

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 8 FIXING SYSTEM

Figure 8-B504

5) While pushing the cleaning belt feeding

roller [4] and the take-up roller [5] toward
the rear, detach the cleaning belt [6].

Caution:

When cleaning the silicone oil pan, be
sure to remove the silicone oil collecting
in the oil pan [7] found under the clean-
ing belt feeding roller.

[5]

[6]

[4]

Figure 8-B503

[7]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 358 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: