Canon ImageRunner 600 Скачать руководство пользователя страница 101

Страница: 101 / 875

3-28

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A

CHAPTER 3 ORIGINAL EXPOSURE SYSTEM

Figure 3-C501

Figure 3-C502

Claw

[1]

[2]

[3]

[4]

PCBs

Removing the Light Intensity
Control PCB

1) Remove the right glass retainer.
2) Remove the copyboard glass.
3) Remove the screw [1] from the No. 1 mir-

ror mount; then, while pushing down the
three claws, free the intensity control PCB
holder.

4) Disconnect the connector [2] (J165), and

remove the screw [3]; then, detach the
light intensity control PCB [4].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 101 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: