Canon ImageRunner 600 Скачать руководство пользователя страница 321

Страница: 321 / 875

CHAPTER 7 PICK-UP/FEEDING SYSTEM

7-82

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

[1] [2][3] [4]

[5]

[6] [7]

[10]

[8]

[9]

[1]

Removing the Duplexing Reversal
Sensor

1) Remove the duplexing unit from the

copier.

2) Remove the front cover.
3) Remove the motor support plate.
4) Remove the following from the front side

of the reversing roller shaft [1]:
• E-ring [2]
• Gear [3] and parallel pin [4]
• E-ring [5]
• Spacer [6]
• Bearing [7]

5) Remove the following from the rear of the

reversing roller shaft [1]:
• E-ring [8]
• Spacer [9]
• Bearing [10]

Figure 7-F812

Figure 7-F813

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 321 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: