Canon ImageRunner 600 Скачать руководство пользователя страница 485

Страница: 485 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

10-37

CHAPTER 10 SIDE PAPER DECK

Figure 10-C313

Figure 10-C314

8) Insert a hex wrench [11] into the hole of

the lifter drive shaft [10] to hold it in place
(thereby preventing it from rotating).

Caution:

If you fail to prevent the lifter drive shaft
from rotating, the lifter cable will be-
come slack as soon as you remove the
lifter motor unit.

9) Remove five screws [12], and detach the

lifter motor unit [13].

[10]

[11]

[12]

[13]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 485 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: