Canon ImageRunner 600 Скачать руководство пользователя страница 372

Страница: 372 / 875

8-44

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 8 FIXING SYSTEM

Figure 8-F504

Figure 8-F505

[12]

[11]

[10]

[9]

[8]

5) Remove the E-ring [8], one-way gear [9],

and bearing [10]; then, remove the two E-
rings [11], and detach the two rollers [12].

Caution:

Each roller is equipped with a parallel
pin. Take care not to lose it.

Removing the Internal Delivery
Roller

1) Remove the fixing assembly from the

copier.

2) Remove the spring [2], three E-rings [3],

and bushing [4] at the front; then, detach
the drive gear [5].

[1]

[4]

[2]

[3]

[5]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 372 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: