Canon ImageRunner 600 Скачать руководство пользователя страница 472

Страница: 472 / 875

10-24

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 10 SIDE PAPER DECK

Figure 10-A306

Figure 10-A307

Removing the Rear Cover

1) Release the deck, and remove the six

screws [1]; then, detach the rear cover [2].

Removing the Right Cover

1) Remove the three screws [1], and move

the right cover [2] to the front; then, re-
move it toward the rear.

[1]

[2]

[1]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 472 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: