Canon ImageRunner 600 Скачать руководство пользователя страница 286

Страница: 286 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-47

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[1]

[2]

[1]

[5]

[4]

[3]

(front of the
copier)

[8]

[6]

[7]

Figure 7-A807

Figure 7-A808

Figure 7-A809

Removing the Feeding Roller

1) Remove the pickup roller, and remove the

stop ring.

2) Remove the two screws [1], and detach

the manual feed tray guide [2].

3) Remove the stop ring [3] from the front of

the feeding roller assembly, and move the
feeding roller assembly [5] together with
the timing belt [4] to detach.

Orientation of the Feeding Roller

When mounting the feeding roller [6] to

the manual feed tray pickup assembly, be sure
that the belt pulley [7] and the round marking
[8] are toward the copier's front.

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 286 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: