Canon ImageRunner 600 Скачать руководство пользователя страница 364

Страница: 364 / 875

8-36

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 8 FIXING SYSTEM

Figure 8-C510

Figure 8-C511

5) Remove the two thermistor retaining

springs [4], and remove the main ther-
mistor [5].

Removing the Sub Thermistor

1) Slide the fixing assembly out of the

copier.

2) Remove the fixing cleaning belt and the

oil pan.

3) Remove the fixing harness cover.
4) Disconnect the connector [1], and remove

the screw [2]; then, remove the sub ther-
mistor assembly [3].

5) Remove the screw [4], and remove the sub

thermistor [5].

[4]

[5]

[3]

[2]

[1]

[4]

[5]

Figure 8-C512

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 364 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: