Canon ImageRunner 600 Скачать руководство пользователя страница 322

Страница: 322 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-83

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[11]

(front)

[11]

(rear)

[12]

Figure 7-F814

Figure 7-F815

Figure 7-F816

6) Release the front and rear springs [11] of

the reversing guide.

7) While lifting the reversing guide, detach

the reversing roller [12].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 322 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: