Canon ImageRunner 600 Скачать руководство пользователя страница 216

Страница: 216 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

6-57

CHAPTER 6 IMAGE FORMATION SYSTEM

Figure 6-B707

Figure 6-B708

[1]

[2]

[3]

[1]

[2]

[3]

Removing the Primary Charging
Assembly

1) Open the front cover.
2) Remove the inside cover (process unit).
3) Disconnect the connector [1]; while shift-

ing the charging assembly fixing plate [2]
to the left, slide out the primary charging
assembly [3].

Removing the Pre-Transfer
Charging Assembly

1) Open the front cover.
2) Remove the inside cover (process unit).
3) Disconnect the connector [1]; while shift-

ing the charging assembly fixing plate [2]
to the right, slide out the pre-transfer
charging assembly [3].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 216 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: