Canon ImageRunner 600 Скачать руководство пользователя страница 375

Страница: 375 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

8-47

CHAPTER 8 FIXING SYSTEM

Removing the Reversal Sensor

1) Remove the fixing assembly from the

copier.

2) Open the upper delivery assembly; then,

remove the screw [1], and detach the re-
versal sensor [2].

Removing the Fixing/Feeding Unit
Outlet Sensor

1) Remove the screw [1] from the bottom of

the fixing/feeding unit, and detach the fix-
ing/feeding outlet sensor [2].

Figure 8-G504

Figure 8-G505

[1]

[2]

[1]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 375 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: