Canon ImageRunner 600 Скачать руководство пользователя страница 522

Страница: 522 / 875

11-28

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 11 INSTALLATION

2) Connect the connector [3] of the power

supply unit to the connector [4] of the con-
troller as shown.

3) Remove the four screws [6], and detach

the face plate [5] from the copier's rear
cover.

4) Connect the connector J521 [7] of the

copier and the cable of the controller.

Figure 11-502

Figure 11-503

Figure 11-504

[4]

[3]

[5]

[6]

[7]

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 522 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: