Canon ImageRunner 600 Скачать руководство пользователя страница 320

Страница: 320 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

7-81

CHAPTER 7 PICK-UP/FEEDING SYSTEM

[2]

[1]

[3]

[2]

[4]

[5]

[6]

Figure 7-F810

Figure 7-F811

Removing the Lower Feeding
Right Clutch

1) Remove the duplexing unit from the

copier.

2) Remove the front cover.
3) Disconnect the connector [1], and remove

the two screws [2]; then, detach the latch
plate [3].

4) Remove the bearing [4] and spacer [5];

then, detach the lower feeding right clutch
[6].

Содержание ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ImageRunner 600

Отзывы:

Canon ImageRunner 600, Руководство по обслуживанию, Страница: 320 / 875

Результаты поиска

Содержание ImageRunner 600

Отзывы: