99
To continue in setup, press the
▼
Navigation Button [oval 16]
to move the cursor next to:
BACK
TO CURTAIN CODE PROG
. Press the
Set Button [oval 18]
. Press the
▼
Navigation Button
[oval 16]
again to move the cursor next to:
BACK TO CURTAIN CNTL SETUP
. Press the
Set
Button [oval 18]
. The
CURTAIN CONTROL SETUP
screen will appear.
To program
TV/PROJECTOR ON/OFF
,
DRAPES OPEN/CLOSE
, LIGHTING
ON/OFF
, press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor next to:
BACK TO REM CNTL SETUP
.
Press the
Set Button [oval 18]
. See the Screen and Lighting sections.
If a particular brand or functional codes from a source type cannot be found in the on-board IR
code Library, IR commands for Curtain OPEN/CLOSE can be taught to the AVR from the original
equipment remote. To teach Curtain OPEN/CLOSE codes to the AVR, proceed to section:
Learn
Code
.
Curtain Program (Learn Code)
To teach the AVR21EN Screen ON/OFF codes, in the
CURTAIN CONTROL SETUP
screen, press
the
▼
Navigation Button [oval 16]
to move the cursor next to:
LEARN CODE
. Press the
Set
Button [oval 18]
. The
CURTAIN CODE LEARN
screen will appear.
With the cursor positioned next to
USING THE
◄
►
KEYS
line, press the
Set Button [oval 18]
.
The message:
USING THE
◄
/
►
KEYS SELECT FUNCTION TO BE PROG
will start to flash,
indicating a function can be selected for learning. Press the
◄
Navigation Button [oval 16]
to
select
CURTAIN POWER ON
. When the ON function appears, press the
▼
Navigation Button
[oval 16]
to position the cursor next to
POINT ORIGINAL REM TO AVR DISPLAY PRESS KEY
.
Press the
Set Button [oval 18]
. The
POINT ORIGINAL…
message will start to flash. Point the
original remote toward the
IR Sensor [square 31]
in the
Information Display [square 25]
on the
AVR front panel and press the button with the original code until the message stops flashing and
CODE LEARNED
appears on screen.
The cursor will automatically return to the
USING THE
◄
►
KEYS
line. Repeat steps above to
program the OFF command.
If
CODE NOT LEARNED
appears, try to learn the code again. In some cases, it may be a good
idea to replace the original remote’s batteries to improve signal output from the remote. In some
cases, there will be codes that the AVR just is not capable of learning. Contact the Audioaccess
Technical Service Department for advice in such a case.
Test Curtain Code
To test the Curtain ON/OFF commands the AVR21ENR1 remote must be configured for HT
MASTER ON/OFF ENABLED.
Press and hold the
REM MENU Button [oval 36]
on the remote until the
Set Button [oval 18]
lights red. Press the
▲
Navigation Button [oval 16]
TWICE so HT MASTER ON/OFF shows in
the remote’s LCD Information Display. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button [oval 16]
until ENABLED appears in the display. Press the
Set Button [oval
18]
. SAVING will appear briefly in the remote display and then SAVED will flash four times. The
HT MASTER ENABLED configuration is now set and the remote will automatically return to
operational mode.
Press the
TV Button [oval 6]
on the remote. TV should appear in the remote display. Press the
ON Button [oval 2]
on the remote. The Curtain just configured should turn ON or open. Press
the
OFF Button [oval 1]
on the remote. The Curtain should turn OFF or close. NOTE: If the
Curtain does not respond, be sure an IR emitter is properly connected to the
Control Out All
Jack [circle 35]
on the AVR rear panel and properly attached to the Curtain.
To return to normal operation mode press the
AVR Button [oval 5]
on the AVR21ENR1 remote.
Содержание AVR21EN
