93
Test Screen Code
To test the Screen ON/OFF commands the AVR21ENR1 remote must be configured for HT
MASTER ON/OFF ENABLED.
Press and hold the
REM MENU Button [oval 36]
on the remote until the
Set Button [oval 18]
lights red. Press the
▲
Navigation Button [oval 16]
TWICE so HT MASTER ON/OFF shows in
the remote’s LCD Information Display. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button [oval 16]
until ENABLED appears in the display. Press the
Set Button [oval
18]
. SAVING will appear briefly in the remote display and then SAVED will flash four times. The
HT MASTER ENABLED configuration is now set and the remote will automatically return to
operational mode.
Press the
TV Button [oval 6]
on the remote. TV should appear in the remote display. Press the
ON Button [oval 2]
on the remote. The Screen just configured should turn ON or drop. Press the
OFF Button [oval 1]
on the remote. The Screen should turn OFF or retract. NOTE: If the Screen
does not respond, be sure an IR emitter is properly connected to the
Control Out All
Jack
[circle 35]
on the AVR rear panel and properly attached to the Screen.
To return to normal operation mode press the
AVR Button [oval 5]
on the AVR21ENR1 remote.
Voltage Trigger (Screen)
The
Trigger Out [circle 38]
on the AVR rear panel can be controlled in two modes:
AVR ON/OFF:
Simply put, when the AVR turns ON, the
Trigger Out [circle 38]
outputs a
co12VDC control voltage. In this case with the
Trigger Out [circle 38]
being used to
drop a screen, the screen will drop as soon as the AVR is turned ON. When the AVR is turned
OFF, the
Trigger Out [circle 38]
drops to 0 VDC, and the screen retracts. NOTE: If the AVR
turns on to Multiroom Mode, the
Trigger Out [circle 38]
will stay at 0VDC until the Main Room is
turned ON.
MANUAL VIA REMOTE:
In this mode, the
Trigger Out
Jack [circle 38]
is controlled with the
Trigger Button [oval 50]
on the AVR21ENR1 remote. When the AVR is turned ON, the
Trigger
Out
has an output of 0VDC. When the
Trigger Button [oval 50]
on the remote is pressed, the
Trigger Out
goes to +12VDC, in this case to drop a screen. Press the
Trigger Button [oval 50]
again, the voltage is cut and the screen retracts.
To configure the AVR21EN
Trigger Out
Jack [circle 38]
to drop a projection screen when the
Main Room is turned ON:
Press the
Menu Button
on the remote to bring the
MAIN MENU
to the screen. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
REMOTE CONTROL SETUP
line.
Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 1
screen will appear. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
GO TO REMOTE CNTL 2
.
Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 2
screen will appear.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
ASSIGN
TRIGGER OUT
line. Press the
◄
/
►
Navigation Button [oval 16]
until
SCRN
appears. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
SCREEN CONTROL
. Press the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed
to the
CONTROL
line. Press the
◄
/
►
Navigation Button [oval 16]
to select the preferred mode.
Press
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
BACK TO REM
CNTL SETUP
line. Press the
Set Button [oval 18]
.
To test the SCREEN UP/DOWN commands with AVR ON/OFF, turn the AVR OFF and manually
raise the screen. To test ON, either: press the
Standby/ON Button [square 2]
on the AVR front
Содержание AVR21EN
