100
Voltage Trigger (Curtain)
The
Trigger Out [circle 38]
on the AVR rear panel can be controlled in two modes:
AVR ON/OFF:
Simply put, when the AVR turns ON, the
Trigger Out [circle 38]
outputs a
co12VDC control voltage. In this case with the
Trigger Out [circle 38]
being used to
open a curtain, the curtain will open as soon as the AVR is turned ON. When the AVR is turned
OFF, the
Trigger Out [circle 38]
drops to 0 VDC, and the curtain closes. NOTE: If the AVR turns
on to Multiroom Mode, the
Trigger Out [circle 38]
will stay at 0VDC until the Main Room is
turned ON.
MANUAL VIA REMOTE:
In this mode, the
Trigger Out
Jack [circle 38]
is controlled with the
Trigger Button [oval 50]
on the AVR21ENR1 remote. When the AVR is turned ON, the
Trigger
Out
has an output of 0VDC. When the
Trigger Button [oval 50]
on the remote is pressed, the
Trigger Out
goes to +12VDC, in this case to drop a screen. Press the
Trigger Button [oval 50]
again, the voltage is cut and the screen retracts.
To configure the AVR21EN
Trigger Out
Jack [circle 38]
to open a curtain when the Main Room
is turned ON:
Press the
Menu Button
on the remote to bring the
MAIN MENU
to the screen. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
REMOTE CONTROL SETUP
line.
Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 1
screen will appear. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
GO TO REMOTE CNTL 2
.
Press the
Set Button [oval 18]
. The
REMOTE CNTL SETUP 2
screen will appear.
Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
ASSIGN
TRIGGER OUT
line. Press the
◄
/
►
Navigation Button [oval 16]
until
SCRN
appears. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to
CURTAIN CONTROL
. Press
the
Set Button [oval 18]
. Press the
▼
/
▲
Navigation Button [oval 16]
so that the cursor is
pointed to the
CONTROL
line. Press the
◄
/
►
Navigation Button [oval 16]
to select the preferred
mode. Press
▼
/
▲
Navigation Button [oval 16]
so that the cursor is pointed to the
BACK TO
REM CNTL SETUP
line. Press the
Set Button [oval 18]
.
To test the CURTAIN OPEN/CLOSE commands with AVR ON/OFF, turn the AVR OFF and
manually close the curtain. To test ON, either: press the
Standby/ON Button [square 2]
on the
AVR front panel; or press the
ON Button [oval 2]
on the AVR21ENR1 remote. The AVR should
turn ON and the curtain should open.
To test OFF, either: press the
Standby/ON Button [square 2]
on the AVR front panel; or: press
the
OFF Button
on the AVR21ENR1 remote. The AVR should turn OFF and the curtain should
close.
To test the CURTAIN OPEN/CLOSE commands with MANUAL VIA REMOTE, turn the AVR OFF
and manually close the curtain. Turn the AVR ON by pressing the
Standby/ON Button [square
2]
on the AVR front panel or press the
ON Button [oval 2]
on the remote. (The AVR should be
on, but the curtain should still be closed.) Press the
Trigger Button [oval 50]
on the remote. The
curtain should open. Press the
Trigger Button [oval 50]
again and the curtain should close.
Exit Setup
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
Содержание AVR21EN
