92
Screen Program Code (Automatic)
If ON/OFF codes could not be found by Brand in the Manual Mode, try searching by source type
in the Automatic mode.
In the
SCREEN CODE PROGRAM
screen, press the
▼
/
▲
Navigation Button [oval 16]
to move the
cursor next to:
AUTOMATIC
. Press the
Set Button [oval 18]
. The
SCREEN AUTO PROGRAM
screen will appear.
The
SOURCE
will be fixed as selected (
SCREEN
). Press the
▼
Navigation Button [oval 16]
to
move the cursor next to:
TRY CODES
. Repeatedly press the
◄
or
►
Navigation Button
[oval 16]
to test all selected device type commands until the unit turns off. When the unit turns off, press
the
▼
Navigation Button [oval 16]
to move the cursor next to:
YES
. Press the
Set Button [oval
18]
to ‘save’ the code group. This will set this code group for ON/OFF control of the Screen.
If no further programming is required, press the
AVR Button [oval 5]
on the AVR21ENR1 remote
and then the
Exit Button [oval 17]
to return to normal operation mode.
To continue in setup, press the
▼
Navigation Button [oval 16]
to move the cursor next to:
BACK
TO SCREEN CODE PROG
. Press the
Set Button [oval 18]
. Press the
▼
Navigation Button
[oval 16]
again to move the cursor next to:
BACK TO SCREEN CNTL SETUP
. Press the
Set
Button [oval 18]
. The
SCREEN CONTROL SETUP
screen will appear.
To program
TV/PROJECTOR ON/OFF
,
LIGHTING ON/OFF
,
CURTAIN OPEN/CLOSE
, press the
▼
/
▲
Navigation Button [oval 16]
to move the cursor next to:
BACK TO REM CNTL SETUP
.
Press the
Set Button [oval 18]
. See the Screen and Lighting sections.
If a particular brand or functional codes from a source type cannot be found in the on-board IR
code Library, IR commands for Screen UP/DOWN can be taught to the AVR from the original
equipment remote. To teach Screen UP/DOWN codes to the AVR, proceed to section:
Learn
Code
.
Screen Program (Learn Code)
To teach the AVR21EN Screen ON/OFF codes, in the
SCREEN CONTROL SETUP
screen, press
the
▼
Navigation Button [oval 16]
to move the cursor next to:
LEARN CODE
. Press the
Set
Button [oval 18]
. The
SCREEN CODE LEARN
screen will appear.
With the cursor positioned next to
USING THE
◄
►
KEYS
line, press the
Set Button [oval 18]
.
The message:
USING THE
◄
/
►
KEYS SELECT FUNCTION TO BE PROG
will start to flash,
indicating a function can be selected for learning. Press the
◄
Navigation Button [oval 16]
to
select
SCREEN POWER ON
. When the ON function appears, press the
▼
Navigation Button
[oval 16]
to position the cursor next to
POINT ORIGINAL REM TO AVR DISPLAY PRESS KEY
.
Press the
Set Button [oval 18]
. The
POINT ORIGINAL…
message will start to flash. Point the
original remote toward the
IR Sensor [square 31]
in the
Information Display [square 25]
on the
AVR front panel and press the button with the original code until the message stops flashing and
CODE LEARNED
appears on screen.
The cursor will automatically return to the
USING THE
◄
►
KEYS
line. Repeat steps above to
program the OFF command.
If
CODE NOT LEARNED
appears, try to learn the code again. In some cases, it may be a good
idea to replace the original remote’s batteries to improve signal output from the remote. In some
cases, there will be codes that the AVR just is not capable of learning. Contact the Audioaccess
Technical Service Department for advice in such a case.
Содержание AVR21EN
