APRILIA MSS Mana GT ABS Скачать руководство пользователя

Страница: 59 / 394

Electrical system installation

Motorcycle division

The wiring timing is subdivided in three essential

sections, as indicated in the figure.

1. Front section

2. Central section

3. Rear section

SPECIAL CHECKS FOR THE CORRECT CONNECTION AND LAYING OF CABLES

Carry out the checks described below once the electrical system is refitted, connectors recon-

nected and clamps and retainers restored.

•

For the following connectors, check the connection and the correct tightening of the Sec-

ondary Lock and "mark" the connector with an indelible pen.

1. Instrument panel connector: FRONT SECTION, TABLE J.

2. Handgrip sensor connectors: CENTRAL SECTION, TABLE F.

3. Pick Up Connector: CENTRAL SECTION, TABLE Q.

4. Side Stand Switch Connector.

5. Regulator Connector: CENTRAL SECTION, TABLE H.

6. Front cylinder coil and rear cylinder coil connectors: CENTRAL SECTION, TABLE F.

7. Filter Housing Connectors: CENTRAL SECTION, TABLE F.

8. ECU and Ground Lead Connectors for the filter casing: CENTRAL SECTION, TABLE A.

9. Fuel Pump Connector: CENTRAL SECTION, TABLE F.

10.Key Connector - Right Light Switch Connectors - Left Light Switch Connectors: Connectors inside

the housing behind the radiator: FRONT SECTION, TABLE I.

11.Pedal gear control connector.

12.Pulley position connector.

13.ABS control unit connector

14.Rear and front ABS sensor connector.

•

THE CONNECTORS LISTED ARE CONSIDERED CRITICAL IN COMPARISON WITH

ANY OTHER BECAUSE THE VEHICLE WILL STOP IF THEY ARE ACCIDENTALLY DIS-

CONNECTED.

•

Undoubtedly the connection of the rest of connectors is also important and essential for the

correct operation of the vehicle.

MSS Mana GT ABS

Electrical system

ELE SYS - 59

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды