APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 117

Страница: 117 / 394

Example value:

°C

There is a sensor inside the control unit.

AXONE: STATUSES

AXONE / AUTOMATIC TRANSMISSION system - ECU operation status

Example value:

automatic/manual/from manual to automatic/from automatic to manual/semiautomatic/

start-up/power latch/error

General ECU operation status.

Gearshift mode

Example value:

manual/automatic/semiautomatic/from automatic to manual/from manual to automatic

Gearshift mode setting

Entered ratio

Example value:

gear not defined/first/second/third/fourth/fifth/sixth/seventh/invalid

Performance limitations

Example value:

none/rpm limitation/start-up restriction with side stand down

Rpm limitation: if there is a malfunction in the driving pulley control electrical motor with the engine

running Start-up restriction with side stand down: if the stand is down, the start-up is blocked for safety

reasons due to a system malfunction.

Gearbox fault

Example value:

absent/present

If the status is "present", a malfunction has been detected in the gear system or in one of its components

(mode control or gear control buttons excluded).

Gear calibration

Example value:

absent/present

If the status is "present", a malfunction has been detected in the gear system or in one of its components

(mode control or gear control buttons excluded).

Ignition

Example value:

enabled/disabled

It indicates if the engine can be started through the transmission control unit. In the "conditioned" status,

and depending on the case, ignition may be blocked or enabled but it affects the regular operation

(variator position cannot be modified).

ACTIVATION

Error clearing

The errors stored in the transmission ECU can be deleted.

Errors ambient parameters reading

The ambient conditions at the time of the last detection of the error can be read. Especially the Riding

cycles parameter without detection of the error indicates how many times the key ON/OFF operation

has been performed from the last reading of the error.

ERRORS

MSS Mana GT ABS

Electrical system

ELE SYS - 117

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды