APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 168

Страница: 168 / 394

Also check the diameter of the bearings on the fly-

wheel cover and on the engine crankcase.

Characteristic

Diameter of bearing on the flywheel cover

12 (+0.034; - 0.016) mm (0.47000 (+0.0013;

-0.0006) in)

Characteristic

Diameter of bearing on the engine crankcase

12 (+0.034; - 0.016) mm (0.47000 (+0.0013;

-0.0006) in)

NOTE

THE TORQUE LIMITER IS EQUIPPED WITH 4 GEARS THAT FUNCTION AS CLUTCH DRIVING
PLATES.

Driven plates consist of 4 Belleville springs with

grooved profiles; this assembly allows transmitting

torques below 100 Nm (73.75 lbf ft).

In case of incorrect start-up procedures, the torque

limiter prevents any kicks, resulting in inversion of

rotation direction of the crankshaft which would

impair the engine structure.

The limiter assembly cannot be overhauled. In case of clearly visible irregularities on the toothed discs,

replace the assembly.

Engine

MSS Mana GT ABS

ENG - 168

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды