manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 132

from PIN A6 to PIN C5 or that PIN C5 does not have a ground connection: check the trans-

mission ECU connector and the gearshift control connector: if they are not OK, restore; if

they are OK, check continuity on the black/purple cable: if it is not OK, restore; if it is OK,

check continuity on the blue/black cable from the gearshift control connector to PIN C5: if it

is not OK, restore; if it is OK, check continuity of the gearshift control from the gearshift

control connector (between red cable and blue cable): if it is not OK, replace the control; if

it is OK, check, with key set to KEY ON, that there is no ground connection in the blue/black

cable and then replace the transmission ECU. CASE 4) if both voltages are above 1 V

(approximately battery voltage), with control activated, it means that there is an interruption

on the circuit from PIN C4 to PIN C5: check the transmission ECU connector and the gear-

shift control connector: if they are not OK, restore; if they are OK, check continuity on the

blue/purple cable: if it is not OK, restore; if it is OK, check, with control activated, that there

is not continuity on the gearshift control from the gearshift control connector (between red

cable and brown cable) and then replace the control.

•

If the control is blocked: check the control mechanically: if it is not OK, restore; if it is OK, it

means that on the diagnosis instrument the status of "Pedal gear downshift control" indicates

"Pressed": the gear downshift control must be replaced.

Gearshift lever on the handlebar

GEARSHIFT CONTROL ON HANDLEBAR

Function

To tell the transmission ECU that the driver wishes

to change the variator transmission ratio (if trans-

mission in manual mode).

Operation / operating principle

Either control (+) or (-) is made up of a deviator

with both outputs electrically connected to the in-

strument panel: at the same time, the instrument

panel sends the requested command to the trans-

mission ECU, via CAN line.

Level in wiring diagram:

 transmission manage-

ment

Position:

•

handlebar gearshift control on vehicle:

left light switch

•

connector: behind front headlight, un-

der the instrument panel

Electrical system

MSS Mana GT ABS

ELE SYS - 132

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды