manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 187

- Check that there are no signs of wear on the fay-

ing surface with the set screw articulated end and

that its surface is smooth and not concave.

- If no anomalies are found during the above

checks, the same valves can be reused.

For better sealing results, it is advisable to grind

the valves. Grind the valves gently with fine-

grained lapping compound. Upon grinding, keep

the cylinder head with the valve axles in a hori-

zontal position. This will prevent the lapping com-

pound residues from penetrating into the stem-

valve guide coupling.

CAUTION

TO AVOID SCORING THE FAYING SURFACE, DO NOT RO-
TATE THE VALVE WHEN NO LAPPING COMPOUND IS
LEFT. CAREFULLY WASH THE CYLINDER HEAD AND THE
VALVES WITH A SUITABLE PRODUCT FOR THE TYPE OF
LAPPING COMPOUND BEING USED.

CAUTION

DO NOT CHANGE THE VALVE FITTING POSITION (RH -
LH).

See also

Installing the

cylinder head

Inspecting the valve sealings

- Fit the valves into the cylinder head.

- Alternatively test the intake and exhaust valves.

- The test should be carried out by filling the mani-

fold with fuel and checking that the head does not

ooze through the valves when they are just press-

ed by the fingers.

See also

Installing the

cylinder head

MSS Mana GT ABS

Engine

ENG - 187

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды