APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 296

Страница: 296 / 394

•

Fit the centring plate.

•

Fit the pumping member together with

the centring plate in the sleeve.

•

Insert the special washer in the screw.

•

Scatter the screw thread with the spe-

cific product.

•

Tighten the screw.

UPON REFITTING, REPLACE THE SAFETY WASHER WITH
A NEW ONE

Recommended products

Loctite 242

Medium strength threadlock

NOTE

THE FOLLOWING OPERATIONS REFER TO THE SHOWA FORKS.

NOTE

THE OPERATIONS DESCRIBED BELOW ARE VALID FOR BOTH STEMS.

•

Fit the dust gaiter (1), seeger ring (2),

oil seal (3), ring (4), guide bushing (5)

and sliding bushing (6) on the stem.

CAUTION

FIT THE GUIDE BUSHING AND THE SLIDING BUSHING
WITH CAUTION.
GUIDE BUSHING (5) IS THICKER THAN SLIDING BUSHING
(6).

•

Fit the stem into the sleeve and place

the special fitting tool for fitting the D.

43 oil seal between the Seeger ring

and the oil seal.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

Suspensions

MSS Mana GT ABS

SUSP - 296

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды