APRILIA MSS Mana GT ABS Скачать руководство пользователя

Страница: 78 / 394

3. Pulling the cables slightly from the back of the connector in order to check the correct position of

terminals on the connector and of the cable on the terminal.

CONTINUITY check

Check goal:

this control is to check that there are not any circuit interruptions nor excessive resistance,

for instance caused by rust, on the two terminals being inspected.

Tester:

set the tester on the "continuity" symbol and place the tester probes on the two circuit ends:

the tester emits a sound signal only if there is continuity; the tester can also be set to the Ohm symbol

to check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION: THE CIRCUIT SHOULD NOT BE ENERGISED, OTHERWISE THE TEST IS IRRELE-

VANT.

GROUND CONNECTION check

Check goal:

this control is to check if a cable or a circuit is in contact with the vehicle ground (-)

connection.

Tester: set the tester on the "continuity" symbol and place one tester probe on the vehicle ground

connection (or on the battery - terminal) and the other probe on the cable being inspected: the tester

sends out a sound signal only if there is continuity. The tester can also be set to the Ohm symbol to

check that the circuit resistance is null or a few tenths of an Ohm.

CAUTION! IF THERE IS A GROUND CONNECTION COMING FROM THE CONTROL UNIT, MAKE

SURE THAT DURING THE TEST THE CONTROL UNIT IS GROUND CONNECTED TO THE CIR-

CUIT.

VOLTAGE check

Check goal:

this control is to check if a cable is energised, i.e. if it receives power supply from the

battery or the control unit.

Tester:

set the tester on the direct current symbol and place the tester red probe on the cable being

inspected and the black probe on the vehicle ground connection (or on the battery - terminal).

CAUTION

IN CASE OF TEMPORAL MALFUNCTIONING, CARRY OUT ALL DUE CHECKS LOOKING FOR
FAULT BY MOVING SLIGHTLY THE CABLE HARNESS BEING INSPECTED.

Dashboard

In case of failure, a different icon is displayed ac-

cording to the cause at the bottom of the display.

SERVICE ALARM

In case of failure found in the instrument panel or

in the electronic control unit, the instrument panel

signals the failure by displaying the SERVICE icon

and the red general warning light comes on.

Electrical system

MSS Mana GT ABS

ELE SYS - 78

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Похожие инструкции для MSS Mana GT ABS

Бренды по названию

Популярные бренды