APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 197

Страница: 197 / 394

Disassembling the piston

- Remove the head.

- Remove the 2 piston pin snap rings operating

through the specific slots.

- Slide off the pin and remove the piston.

NOTE

USE PAPER OR A CLOTH TO CLOSE THE CYLINDER
HOUSING MOUTH ON THE CRANKCASE TO PREVENT
ONE OF THE TWO PIN SNAP RINGS FROM FALLING IN-
SIDE.

- Remove the piston sealing rings and the scraper

ring.

CAUTION

PAY ATTENTION TO THE FITTING POSITIONS OF THE
RINGS TO PREVENT INVERTING THE POSITION IN CASE
THEY ARE REUSED.

NOTE

BE CAREFUL NOT TO DAMAGE THE SEALING RINGS
DURING REMOVAL.

See also

Removing the

cylinder head

Checking the cylinder

•

All seal surfaces must be clean and flat.

•

Make sure all threads are in proper conditions.

•

Check cylinder sliding surface for signs of friction and scratches. Also check the seal sur-

faces for damages.

CAUTION

IF THE GROOVES ON THE CYLINDER LINER ARE EVIDENT, REPLACE THE CYLINDER AND
THE PISTON.

•

Clean off lime scales on the cylinder cooling slots.

MSS Mana GT ABS

Engine

ENG - 197

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды