manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 95

Engine temperature sensor

ENGINE TEMPERATURE SENSOR

Function

it tells the engine temperature to the control unit so

as to optimise its operation.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in wiring diagram:

Temperature sensors

Location:

•

on the vehicle: rear cylinder, internal

area

•

connector: on the sensor

Electrical characteristics:

•

Resistance at 25°: 2.05 kOhm +/- 100

Ohm

•

Resistance at 60°: 575 Ohm +/- 15

Ohm

•

Resistance at 90°: 230 Ohm +/- 5 Ohm

Pin-out:

•

Orange: 0-5 V signal: PIN B1

•

Grey: Ground connection: PIN B2

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: FUEL INJECTION SYSTEM

PARAMETERS

Engine temperature

Example value: 75° C

In case of recovery, this value is set by the control unit.

ELECTRICAL ERRORS

engine temperature sensor P0115

 - open circuit, shorted to positive / shorted to negative.

Error cause

MSS Mana GT ABS

Electrical system

ELE SYS - 95

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды