APRILIA MSS Mana GT ABS Скачать руководство пользователя страница 245

Страница: 245 / 394

Refitting the driven half-pulley bearing

- Fit a new roller bearing with the specific tool.

NOTE

PLACE THE BEARING WITH THE WORDS AND THE BUILT-
IN OIL SEAL FACING OUTWARDS.

- Properly support the half-pulley to prevent damaging the threading.

If you are working on the driven pulley assembly fully fitted, use the specific tool.

Specific tooling

020478Y

Punch for roller casing

AP8140180

Extractor for bushings

- Fit a new ball bearing with the specific tool.

Specific tooling

020376Y

Adapter handle

020477Y

37-mm Adaptor

020364Y

25-mm Guide

- Fit the Seeger ring.

Refitting the driven pulley

- Fit the new oil seals.

- Fit the new O-rings.

NOTE

THE O-RINGS COME IN TWO DIFFERENT SIZES. THE LARGE ONE IS FITTED ON THE MACHIN-
ING END RADIUS; AT THE BASE OF THE HALF-PULLEY.

MSS Mana GT ABS

Engine

ENG - 245

Содержание MSS Mana GT ABS











































































































































































































































































































































































































Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды

APRILIA MSS Mana GT ABS, Руководство по обслуживанию станции

Результаты поиска

Содержание MSS Mana GT ABS

Отзывы:

Бренды по названию

Популярные бренды